224 lines
5.3 KiB
C
224 lines
5.3 KiB
C
#ifndef __GUI_H
|
||
#define __GUI_H
|
||
|
||
#include <rtthread.h>
|
||
|
||
#define LINE_TOTAL_NUM 4 //总测量线路数量
|
||
#define ANALOG_CH_NUM 12 //模拟量通道数
|
||
|
||
#define GUI_SIZE sizeof(gui_in_04reg_t)
|
||
/***********************************************************************小核数据 -> 大核****************************************************************************/
|
||
|
||
//实时量
|
||
typedef struct
|
||
{
|
||
//三相电压
|
||
float Ua; //A相电压
|
||
float Ub; //B相电压
|
||
float Uc; //C相电压
|
||
|
||
//三相电流
|
||
float Ia; //A相电流
|
||
float Ib; //B相电流
|
||
float Ic; //C相电流
|
||
|
||
//有功功率
|
||
float Pa;
|
||
float Pb;
|
||
float Pc;
|
||
float Pt; //总有功功率
|
||
|
||
//无功功率
|
||
float Qa;
|
||
float Qb;
|
||
float Qc;
|
||
float Qt; //总无功功率
|
||
|
||
//视在功率
|
||
float Sa;
|
||
float Sb;
|
||
float Sc;
|
||
float St; //总视在功率
|
||
|
||
//功率因数
|
||
float PFa;
|
||
float PFb;
|
||
float PFc;
|
||
float PFt; //总功率因数
|
||
|
||
//线电压
|
||
float Uab;
|
||
float Ubc;
|
||
float Uca;
|
||
|
||
//频率
|
||
float frq;
|
||
|
||
// float rev1[10];//10个备用
|
||
|
||
}measure_unit_t;
|
||
|
||
//B码对时，时间数据
|
||
typedef union
|
||
{
|
||
uint8_t b_code[6];
|
||
|
||
struct
|
||
{
|
||
uint8_t ascii_s_unit : 4;
|
||
uint8_t ascii_s_ten : 4;
|
||
uint8_t ascii_min_unit : 4;
|
||
uint8_t ascii_min_ten : 4;
|
||
uint8_t ascii_hour_unit : 4;
|
||
uint8_t ascii_hour_ten : 4;
|
||
uint8_t ascii_m_day_unit: 4;
|
||
uint8_t ascii_m_day_ten : 4;
|
||
uint8_t ascii_month_unit: 4; //4bit
|
||
uint8_t ascii_month_ten : 4; //4bit
|
||
uint8_t ascii_year_unit : 4; //4bit
|
||
uint8_t ascii_year_ten : 4; //4bit
|
||
}time;
|
||
}b_code_t;
|
||
|
||
|
||
//事件标志
|
||
typedef struct
|
||
{
|
||
uint32_t timestamp; //事件发生时间，时间戳
|
||
uint16_t ms; //事件发生的毫秒时刻
|
||
uint8_t line_num; //高4位：线路号 (0 = 装置，1 = 线路1，2 =线路2， 3 = 线路3， 4 = 线路4，5= AI越限)
|
||
//低4位：事件类型(1 = 保护、2 = 动作、3 = 报警、4 = 操作)
|
||
uint8_t code; /*事件代码：保护类：1 = pt 断线， 2 = CT断线，其它事件依次编号
|
||
报警类：1 = 过压，2 = 过流，3 = ai，4 = ao
|
||
动作类：路数
|
||
*/
|
||
int16_t value; //动作值， 保护类、报警类和AI越限类→事件发生时刻的监测值、动作类→开入分/合状态（0分、非0合）
|
||
}event_t;
|
||
|
||
|
||
//小核数据 -> 大核
|
||
typedef struct
|
||
{
|
||
measure_unit_t measure_unit[LINE_TOTAL_NUM];//总共4条线路，按序排列
|
||
float a_in[8]; //模拟量输入
|
||
b_code_t b_code; //B码对时
|
||
uint16_t d_in; //数字量，开入
|
||
uint16_t d_out; //开出，读开出状态
|
||
uint16_t evt_f; //事件个数，读取到事件个数非0时，立即读取输入寄存器里的事件内容
|
||
|
||
}gui_in_04reg_t;//读输入寄存器数据
|
||
|
||
union gui_t
|
||
{
|
||
uint8_t buf[GUI_SIZE];
|
||
gui_in_04reg_t sub;
|
||
};
|
||
|
||
|
||
typedef struct
|
||
{
|
||
event_t event;
|
||
|
||
}gui_in_03reg_t;//读保持寄存器事件数据
|
||
|
||
typedef struct
|
||
{
|
||
uint16_t a_in; //数字量，开入
|
||
|
||
}gui_in_02reg_t;//读离散输入寄存器数据
|
||
|
||
|
||
/***********************************************************************大核数据 -> 小核****************************************************************************/
|
||
|
||
//串口参数设置
|
||
typedef struct
|
||
{
|
||
uint32_t baud_tate; //波特率 ： 9600 115200（默认）
|
||
uint8_t parity; //校验位 ： 0 = 无校验， 1 = 奇校验， 2 = 偶校验
|
||
uint8_t data; //数据位 ： 0 = 8位
|
||
uint8_t stop; //停止位 ： 0 = 1位， 1 = 2位
|
||
uint8_t protocol; //通讯协议 ：0 = 无协议，1 = modbus
|
||
}com_param_t;
|
||
|
||
//网口
|
||
typedef struct
|
||
{
|
||
uint8_t id[4];
|
||
uint8_t mask[4];
|
||
uint8_t gateway[4];
|
||
uint8_t protocol; //协议
|
||
uint8_t rev;//保留
|
||
}net_t;
|
||
|
||
//模拟通道参数值
|
||
typedef struct
|
||
{
|
||
uint8_t sig_type;//信号类型 ： 0 = 4~20ma信号， 1 = 1~5V信号
|
||
uint8_t line_sub;//所属线路 ： 1 = 线路1， 2 = 线路2， 3 =线路3， 4 = 线路4， 0 = 装置
|
||
uint8_t att; //类别 : 0 = UA, 1 = UB, 2 = UC, 3 = UAB, 4 = UBC, 5 = UCA, 6 = P, 7 = Q, 8 = F
|
||
uint8_t u_limit; //上限值 :
|
||
uint8_t d_limit; //下限值 :
|
||
}analog_ch_param_t;
|
||
|
||
|
||
//线路定值
|
||
typedef struct
|
||
{
|
||
// uint8_t index; //线路号： 1 = 线路1, 2 = 线路2， 3 = 线路3, 4 = 线路4
|
||
uint8_t limit; //限值：
|
||
uint8_t delay; //延时： [1 ~ 10秒]
|
||
uint8_t out_num; //输出节点： [1 = 开出1、 2 = 开出2、...]
|
||
uint8_t select; //投退： [0 = 不投， 1 = 投入]
|
||
|
||
|
||
}line_param_t;
|
||
|
||
typedef struct
|
||
{
|
||
line_param_t type[7]; //7个类别：电压，电流，差流, 功率，频率，PT断线，CT断线
|
||
uint16_t ct; //ct变比
|
||
uint16_t pt; //pt变比
|
||
}line_type_t;
|
||
|
||
|
||
//AI 报警
|
||
typedef struct
|
||
{
|
||
uint8_t u_limit; //上限值 :
|
||
uint8_t d_limit; //下限值 :
|
||
uint8_t delay; //延时： [1 ~ 10秒]
|
||
uint8_t out_num; //输出节点： [1 = 开出1、 2 = 开出2、...]
|
||
uint8_t select; //投退： [0 = 不投， 1 = 投入]
|
||
}ai_alarm_param_t;
|
||
|
||
|
||
//大核数据 -> 小核
|
||
//设置模拟量，数字量输出
|
||
typedef struct
|
||
{
|
||
uint32_t timestamp; //时间戳，设置时间
|
||
|
||
|
||
com_param_t com_param[4]; //串口参数设置: 小核串口，FPGA串口
|
||
line_type_t line_param[4]; //线路定值设置: 4路定值一起下发
|
||
analog_ch_param_t a_in_param[12]; //12路模拟输入通道设置
|
||
analog_ch_param_t a_out_param[12]; //12路模拟输出通道设置
|
||
ai_alarm_param_t ai_alarm_param[12];//12路模拟输入 报警参数设置
|
||
|
||
}gui_out_03reg_t;//放入保持寄存器中的参数
|
||
|
||
|
||
typedef struct
|
||
{
|
||
|
||
uint16_t d_out; //数字量，开出
|
||
|
||
}gui_out_15reg_t;//放入线圈寄存器中的数
|
||
|
||
typedef struct
|
||
{
|
||
gui_out_03reg_t reg_03;
|
||
gui_out_15reg_t reg_15;
|
||
}param_set_t;
|
||
#endif
|